1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be combined arbitrarily, served as main and secondary injection unit separately for power supply.
2.The larger required power between the injection unit and the clamping unit shall be taken to provide power for injection and clamping.
3.When an injection unit has two kinds of power and it is used as the main injection unit, the larger power shall be taken.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the specification change due to continuous improvement of technology.
7.Due to the different size of selected injection unit, please confirm with the technician when the maximum center hole distance of the fixed platen is not determined.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be arbitrarily combined.
2.The specification of mold opening force is available for the mold opening under high pressure.
3.The specification of mold opening stroke is available for minimum and maximum mold thickness.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the parameter change due to continuous improvement of technology.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be arbitrarily combined.
2.The specification of mold opening force is available for the mold opening under high pressure.
3.The specification of mold opening stroke is available for minimum and maximum mold thickness.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the parameter change due to continuous improvement of technology.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
1.Yellow injection unit (operating side) and green injection unit (non-operating side) can be arbitrarily combined.
2.The specification of mold opening force is available for the mold opening under high pressure.
3.The specification of mold opening stroke is available for minimum and maximum mold thickness.
4.The actual injection volume calculated by GPPS is 0.92 time of the theoretical injection volume.
5.The specification of injection unit is in international units. Calculation formula: theoretical injection volume (cm³) X injection pressure (MPa)/100.
6.No prior notice for the parameter change due to continuous improvement of technology.
※ All the data herein come from Yizumi's factory. Please check the data of the actual customized equipment.
사출기 엠와이글로넷(주)
041.420.6017
shh@myglonet.co.kr
사출기